Latest News

2017 Income Limits Released

by joloughlin

Today the 2017 Income Limits were published with a April 14, 2017 effective date. As per Revenue Ruling 94-57, income limits must be implemented on the effective date or 45 days from the published date, whichever is later, which means this year’s limits must be implemented no later than May 28, 2017.

To access the income limits click the appropriate links below:

Section 8 Income Limit Data Set

Multifamily Tax Subsidy Property (MTSP) Income Limit Data Set

MTSP Income Limit Facts…

  • For each of your Housing Credit and Bond properties, you will turn to the MTSP Income Limit dataset unless your property is subsidy-layered or is eligible for the NNMGI-based income limits.
    • The MTSP Income limits are consisted of:
      • Regular 50% Limits
      • Regular 60% Limits
    • And possibly*…
      • HERA Special 50% Limits
      • HERA Special 60% Limits

*BUT the HERA Special Limits are only published
IF (1) the area was impacted by HUD’s 2007-08 Hold Harmless Policy
AND (2) the Regular limits are less than the HERA Special limits.

  • The 2017 NNMGI figure is $55,200 which results in a 50% NNMGI-Based Limits as follows…
1 Person 2 Person 3 Person 4 Person 5 Person 6 Person 7 Person 8 Person
$19,300 $22,100 $24,850 $27,600 $29,800 $32,000 $34,200 $36,450

To implement the 2017 Limits on your Housing Credit properties…

Housing Credit income limits are based on the building’s placed in service (PIS) date which means you must know the property’s 8609 Line 8b election. If elected… 

  • YES, the project is a multi-building project and the income limits will be based on the FIRST building’s PIS.
  • NO, then each building is its own project and the income limits will be based on EACH building’s PIS date.

To select the correct 50% and/or 60% MTSP income limits for your properties, use the following chart.

To be sure you understand the chart as it applies to 2017, when I reference the…

  • Current Regular Limits… I mean the limits you currently have in place at your property PRIOR to the release of the 2017 limits.
  • New Regular Limits… I mean the 2017 non-HERA Special Limits.
  • End of the New Limit Grace Period… I mean May 28, 2017.

If you need other set-asides percentages (30%, 40%, etc.)…

  • Multiply the applicable 50% figures by 2 and then by the set-aside percentage needed.
  • When this calculation is done, do NOT round the final figures.

If your property is subsidy layered…

  • You must first determine each funding type on the property and to which units these funding sources apply as many are not 100% financed.
  • You then must determine which income limit dataset the funding source uses for its income limits.

Example: HUD financing uses the HUD Income Limit dataset, Bond financing use the MTSP dataset, HOME uses its own income limits which are based on the HUD dataset but further tweaked and isn’t usually available until May or June which means you will continue to use the 2016 HOME limits until the 2017 limits are available. Look to the funding source’s regulatory agreement for this determination which is often found in the Definitions. If you cannot find it, you must contact the funding source to clarify.

  • On a per unit basis, gather the applicable income limits and perform any necessary calculations.
  • Use the lowest of each of these limits OR perform separate certifications for each program attached to the unit using the correct income limit associated with each program.

Example: If you have a unit that is a Low HOME and 50% Tax Credit unit, you must pull the Low Home income limits for the area and the applicable 50% MTSP limits as described above. Use the lower of these 2 limits OR when completing the HOME certification, use the Low HOME limits and then complete the Tax Credit certification using the applicable 50% MTSP limits. For the household to qualify, it must have income below BOTH of these limits.

If you need additional instruction on income limit implementation or need to know how to calculate rents…

To top